2025 Gradall Steel Mill Maintenance Machines XL 4310 V

Information

2025 Gradall Steel Mill Maintenance Machines XL 4310 V

UNIQUE GRADALL BOOM MOVEMENTS FOR EFFICIENT STEEL MILL MAINTENANCE

High Performance Machines for Steel Mill Maintenance

Steel mill maintenance is dirty, hot, rugged work in extreme environments. Gradall and LAG steel mill machines are engineered and manufactured with this environment in mind. The machines’ boom range, swing, and tilt rotation movement allow for precise control, whether performing ladle or BOF furnace maintenance or tap hole cleanout and replacement in confined or crowded work areas.

Features may include:

CHASSIS DESIGN
  • Powered by a single Volvo Penta engine that meets highest global standards including State IV (EU) and Tier-4 Final emissions
  • Crawler or rough terrain rubber tire undercarriage
  • On crawler models, dual range high torque piston motor powers each track, along with three-stage planetary drive, integral speed limiting valve and automatic spring-set hydraulic release wet disc parking brake
BOOM
  • Heavy-duty boom rollers, along with an exceptionally rugged boom and tilt motor at rear end of the boom
  • Full boom performs 360° continuous rotation for efficient prying action at any angle
  • Internal metal hose and tube clamps
ADVANCED SYSTEMS
  • Legendary Bosch Rexroth design and reliability
  • All new, modern high-pressure hydraulic system is electronically controlled with pressure-compensated, load-sensing valves
  • Combined electrical system for chassis and excavator delivers advanced, effective operation
PERFORMANCE
  • Short tail swing to maneuver and work in tight quarters
  • Heavy frame for lateral support
  • Heavy boom cradle

Photos

Highlights

  • Exeter, Rhode Island
  • 2025
  • Gradall
  • Steel Mill Maintenance Machines XL 4310 V
  • ZF Model HL 290
  • Available

Specifications

  • 2025
  • Gradall
  • Steel Mill Maintenance Machines
  • XL 4310 V
  • Wheel
  • Volvo TAD571 VE Tier 4f | Axles: ZF Model 3070 (FTF 2090)
  • 173 hp @ 2200 rpm (129kW) 590 ft lb Torque @ 1100- 1500 rpm (800Nm) | Net Rating: 153 hp @ 2200 rpm (114kW)
  • Inline 4 cylinder
  • 24 volt
  • Rexroth A6 Series, 160cc/Rev
  • ZF Model HL 290
  • 10 x 20 Super-Lug
  • 10 x 20 Super-Lug
  • Two SAE #C31-S 1000 CCA
  • 100 amp alternator
  • 4 cycle
  • Swing speed: 7.0 rpm
  • Rated Boom Force: 22,075 lbs (98.2 kN) | Rated Ripper Tooth Force: 25,405 lbs (113 kN) | Boom Rotating Torque:25,800 ft lb (34,980 Nm) | Boom Rotating Speed: 7.0 rpm
  • One load-sensing, axial piston pump; oil flow: 0-110 gpm (0-435 L/min) | Tandem gear pump (steering, brake/pilot): 10 gpm (38 L/min), 6 gpm (23 L/min)
  • Hoist: 4,900 psi(331 BAR) | Tilt : 4,900 psi(331 BAR) | Swing: 4,200 psi(290 BAR) : Tool: 4,900 psi(331 BAR) | Telescope :4,900 psi (331 BAR) | Propel: 4,900 psi (331 BAR) | Pilot System: 550 psi (38 BAR) | Braking & Steering: 2,400 psi(165 BAR) | Blade & Stabilizers: 4,000 psi(207 BAR)
  • Blade: 1,529 lbs (671 kg) | Maximum slope: 30° | Continuous Boom tilt: 360°
  • Minimum: 25’5” (7.75 m)
  • 22’1” (6.7)
  • 105° boom
  • 38,324 lbs (170 kN)
  • 65 gallons (246 L)
  • Tank: 82 gallons (310 L)
  • 48,862 lbs (22,163 kg)